Meet Latta’s Playgrounds

Certified Playground
Safety Inspector

Wayne Maynard knows safety with over 30 years in the construction industry and numerous playground certifications and installations. He can assess your child’s playground for critical safety issues and provide suggestions on how to keep your little ones away from harm.

Wayne’s Safety Checklist

What dangers are hiding in your child’s playground? A little effort now can save a lot of pain later.


1.) Improper Protective Surfacing

The surface or ground under and around the playground equipment should be soft enough to cushion a fall. Improper surfacing material under playground equipment is the leading cause of playground related injuries. Over seventy percent of all accidents on playgrounds are from children falling. Hard surfaces such as concrete, blacktop, packed earth or grass are not acceptable under play equipment. A fall onto one of these hard surfaces could be life threatening.

There are many surfaces that offer protection from falls. Acceptable surfaces are hardwood fiber/mulch, sand, and pea gravel. These surfaces must be maintained at a depth of twelve inches, be free of standing water and debris, and not be allowed to become compacted. There are also synthetic or rubber tiles and mats that are appropriate for use under play equipment.


2.) Inadequate Fall Zone

A fall zone or use zone is under the area under and around the playground equipment where a child might fall. A fall zone should be covered with protective surfacing material and extend a minimum of six feet in all directions from the edge of stationary play equipment such as climbers and chin up bars. The fall zone at the bottom or exit area of a slide should extend a minimum of six feet from the end of the slide for slides four feet or less in height.

For slides higher than four feet, take the entrance height of the slide and add four feet to determine how far the surfacing should extend from the end of the slide. Swings require a much greater area for the fall zone: The fall zone should extend two times the height of the pivot or swing hanger in front of and behind the swings seats. The fall zone should also extend six feet to the side of the support structure.


3.) Protrusion & Entanglement Hazards

A protrusion hazard is a component or piece of hardware that might be capable of impaling or cutting a child if a child should fall against the hazard. Some protrusions are also capable of catching strings or items of clothing which might be worn around a child’s neck. This type of entanglement is especially hazardous because it might result in strangulation.

Examples of protrusion and entanglement hazards include bolt ends that extend more than two threads beyond the face of the nut, hardware configurations that form a hook or leave a gap or space between components and open “S” type hooks. Rungs or handholds that protrude outward from a support structure may be capable of penetrating the eye socket. Special attention should be paid to the area at the top of slides and sliding devices. Ropes should be anchored securely at both ends and not be capable of forming a loop or a noose.


4.) Entrapment in Openings

Enclosed openings on playground equipment must be checked for head entrapment hazards. Children often enter openings feet first and attempt to slide through the opening. If the opening is not large enough it may allow the body to pass through the opening and entrap the head. Generally, there should be no openings on playground equipment that measure between three and one-half inches and nine inches. Where the ground forms the lower boundary of the opening is not considered to be hazardous. Pay special attention to openings at the top of a slide, openings between platforms and openings on climbers where the distance between rungs might be less than nine inches.


5.) Insufficient Equipment Spacing

Improper spacing between pieces of play equipment can cause overcrowding of a play area which may create several hazards. Fall zones for equipment that is higher than twenty-four inches above the ground cannot overlap. Therefore there should be a minimum of twelve feet in between two play structures. This provides room for children to circulate and prevents the possibility of a child falling off of one structure and striking another structure. Swings and other pieces of moving equipment should be located in an area away from other structures.


6.) Trip Hazards

Trip hazards are created by play structure components or items on the playground. Exposed concrete footings, abrupt changes in surface elevations, containment borders, tree roots, tree stumps and rocks are all common trip hazards that are often found in play environment.

Why use a Certified Playground Safety Inpector?

The CPSI certification program provides the most comprehensive and up-to-date training on playground safety issues including hazard identification, equipment specifications, surfacing requirements and risk management methods.


of all injuries to children 0-4 involve the head and face.


of playground injuries involve falls to the surface.


of childhood injuries happened on public playground equipment


of playground injuries require hospitalization.

Why we are different

The trusted name in education is still making a difference in the way children learn and play!

Latta’s Playgrounds offers everything you need to help your little ones play safely no matter their age or capabilities. In addition to a wide catalogue of playground products and accessories, we offer a full range of services including inspection, consultation, design, delivery, installation, and more!

Request a Free Playground Safety Assessment with Wayne Today!

Does your childs play area meet modern safety standards?

No project is too big or too small!